Fencing cost calculator NZ
A fence in New Zealand costs roughly $200 to $750 per metre supplied and installed in 2026, depending on the material: $200 to $380 for 1.8 metre treated pine paling, $250 to $450 for steel panel, $350 to $650 for aluminium, and $400 to $750 for louvre or premium timber privacy screens. Rural post and rail runs $60 to $150 and wire fencing $25 to $60 per metre. Gates, old fence removal and a hard post line sit on top. Use the calculator below for your numbers.
Fence cost by type, per metre installed
| Fence type | Per metre installed (2026) | Where it makes sense |
|---|---|---|
| Treated pine paling, 1.8m | $200 to $380 | The NZ default boundary fence, stain it or let it grey |
| Steel panel (Colorsteel type), 1.8m | $250 to $450 | Low maintenance, light, suits long straight runs |
| Aluminium slat or panel, 1.8m | $350 to $650 | Street frontages, no rot, coastal grades available |
| Louvre or premium timber privacy | $400 to $750 | Decks, courtyards and screening a neighbour's window |
| Precast concrete panel, 1.8m | $400 to $700 | Noise, fire and security on busy or exposed boundaries |
| Glass or aluminium pool fencing, 1.2m | $450 to $1,000 | Compulsory pool barriers, consent always required |
| Post and rail, lifestyle block | $60 to $150 | Horse paddocks and entranceways |
| Rural wire or stock netting | $25 to $60 | Farm boundaries and subdivision fences |
These are supply and install rates for a fence a crew can walk up to with a post hole borer and a trailer. Lower heights cost less per metre, 2 metre privacy fences cost more, and the labour share rises fast once the post line is on a slope, in rock or behind a 900mm side gate. Our city guides for Wellington, Auckland, Kapiti and Christchurch publish local ranges and shortlists.
The extras that move a fencing quote
| Line item | Indicative cost | When it applies |
|---|---|---|
| Old fence removal and dumping | $25 to $70 per metre | Any replacement fence, dearer for concrete footings |
| Pedestrian gate, hung | $500 to $1,500 each | Side access and front paths |
| Manual double driveway gates | $2,500 to $7,000 | Timber or aluminium, no motor |
| Automated sliding or swing gate | $7,000 to $18,000+ | Motor, sensors, keypad, electrician and trenching |
| Sloping, rocky or hard-access post line | Add 15 to 30% | Hand digging, stepped panels, carrying materials |
| Coastal specification | Add 15 to 25% | Stainless fixings, marine-grade coatings within reach of salt spray |
| High wind zone bracing | Priced into post spec | Bigger posts, deeper footings, closer centres under NZS 3604 zones |
| Boundary survey | $1,000 to $3,000 | When the pegs are missing and the neighbour disputes the line |
The Fencing Act split, and how to actually use it
The Fencing Act 1978 is the reason a boundary fence can cost you half what the quote says. Adjoining owners share the cost of an adequate fence equally unless they agree otherwise. The catch is the process: to compel a contribution you serve a written fencing notice describing the fence, the estimated cost and when work will start. Your neighbour has 21 days to object or propose something different. If they say nothing, they are deemed to have agreed. Build first and bill later and you have no claim at all.
Adequate is the operative word. If you want a 2 metre louvre screen and your neighbour is happy with 1.8 metre paling, you can generally only compel half of the adequate fence, not half of the upgrade. Gates on your side are yours. Fences along a road or road reserve are also yours: councils and road controlling authorities are exempt from contributing. Tick the shared boundary box in the calculator to see what an equal split looks like on your numbers.
Consent, height limits and pool fences
- Fences and hoardings up to 2.5 metres high are exempt from building consent under Schedule 1 of the Building Act 2004. The Building.govt.nz exemption guidance lists the detail. A fence that also works as a retaining wall is a different structure with different rules.
- District plan height rules still apply even when no building consent is needed. Front boundary limits of 1.2 to 1.8 metres are common in residential zones, side boundaries often allow 2 metres, and heritage or character overlays can be tighter. Check your council's district plan before you order materials, because a non-complying fence can need resource consent or come down.
- Residential pool barriers are compulsory and always need building consent. The Building.govt.nz pool barrier guidance sets out the 1.2 metre minimum height, climbable zone rules and the three yearly inspection regime. A pool fence quote that skips the consent is a red flag.
- Before any post hole goes in near the street, check for services. Free plans come from beforeUdig, and a borer through a fibre or gas line is the fastest way to turn a $5,000 fence into a $15,000 one.
How to compare fencing quotes
- Run the calculator with your length, type and site conditions. That bracket is your sanity check for the fence and gates, nothing else.
- Get at least two itemised quotes that state post size and grade, post centres, footing depth and concrete, rail count, paling thickness and the fixings specification.
- Confirm who removes the old fence, where it goes and who pays the dump fee. It is the most common missing line.
- Ask how the wind zone has been allowed for. In Wellington, on the Kapiti Coast and on exposed Canterbury sites this is the line that separates a fence that lasts from one that leans by its second winter.
- If it is a shared boundary, serve the fencing notice before the crew is booked, not after. Keep a copy.
Then pick your contractor from a researched shortlist: browse BuildHub's fencing and gate builder guides by city.
Frequently asked questions
How much does a fence cost per metre in NZ?
As of 2026, a standard 1.8 metre treated pine paling fence runs roughly $200 to $380 per metre supplied and installed. Steel panel fencing sits around $250 to $450 per metre, aluminium slat or panel fencing $350 to $650, louvre or premium timber privacy screens $400 to $750, and precast concrete panels $400 to $700. Rural post and rail is about $60 to $150 per metre and wire or stock netting $25 to $60. These are indicative national ranges: Auckland, Wellington and Queenstown price toward the top, and provincial towns often come in under them.
How much does a 20 metre boundary fence cost?
A 20 metre boundary in 1.8 metre treated pine typically lands between $4,000 and $7,500 installed in 2026, before gates. The same run in aluminium is more like $7,000 to $13,000. Removing an old fence first adds roughly $500 to $1,400 for 20 metres, and a sloping or rocky post line can add 15 to 30 percent because every post hole takes longer. If it is a shared boundary and your neighbour agrees to an equal split under the Fencing Act, your share of the fence itself is half those figures.
Who pays for a boundary fence in New Zealand?
Under the Fencing Act 1978, adjoining owners generally share the cost of an adequate boundary fence equally, unless they agree otherwise. To make a contribution compulsory you must serve a written fencing notice describing the fence, the estimated cost and the start date. The neighbour then has 21 days to object or make a counter proposal; silence is treated as agreement. You cannot simply build the fence and send half the bill afterwards, and councils and road controlling authorities are exempt from sharing the cost of fences along a road boundary.
Do I need a building consent for a fence?
Usually not. Schedule 1 of the Building Act 2004 exempts fences and hoardings up to 2.5 metres high from building consent, so almost every residential boundary fence is exempt work. Height limits in your district plan are a separate question: many councils cap front boundary fences around 1.2 to 1.8 metres in residential zones, and anything over about 2 metres on a side boundary can need resource consent. Pool barriers are the big exception: a swimming pool fence always needs building consent and must comply with the pool safety provisions of the Building Act.
What does a driveway gate cost in NZ?
A single hung timber pedestrian gate runs roughly $500 to $1,500 installed. Manual double driveway gates sit around $2,500 to $7,000 depending on material and span. An automated sliding or swing gate with motor, safety sensors, keypad or intercom and the electrical work typically lands between $7,000 and $18,000 or more, and the trenching and cabling to bring power to the gate line can rival the motor cost if the entrance is far from the house.
Why do fencing quotes differ so much for the same fence?
Most of the gap is in the specification rather than the price per metre. Post size and timber grade, post centres, footing depth and whether posts are concreted, rail count, paling thickness, galvanised versus stainless fixings, capping and whether the old fence removal and dump fees are included all move the number. Two quotes for a 1.8 metre pine fence can be $150 per metre apart and both be honest, because one is a 2.4 metre post centre on 100 by 100 posts and the other a 1.8 metre centre on 125 by 125 posts rated for a high wind zone. Ask for the spec in writing and compare that first.
How accurate is this calculator?
It uses researched 2026 New Zealand ranges and gives you a bracket rather than a fake-precise figure, because ground conditions, wind zone requirements, access and hardware grade genuinely move the price. It covers supply and installation of the fence, optional removal of an old fence and typical gate prices. Retaining walls, landscaping, survey pegs and electrical connections for automation are separate lines on a real quote. Use it to sanity-check quotes, not to replace them.